Short answer: the duty applies to jumbo rolls, not labels
The new duty covers only lightweight thermal paper in so-called jumbo rolls, the mill rolls from which till rolls and labels are only later made. A finished thermal label and a finished till roll for a cash register are outside the scope of the measure. This is not a conclusion by analogy or a cautious interpretation: the Commission wrote it explicitly in the recitals of the regulation when it removed one of the Chinese producers from the sample. We come back to this in the third section, because it is the strongest evidence in the whole case.
It is worth remembering a second point straight away, because reports state it inaccurately. The rate of 28.8% is not the general rate. It was given to one Chinese producer that cooperated in the proceeding. All other imports from China are subject to the rate of 70.5%, and the difference between the two figures decides whether a delivery still makes economic sense or none at all.
What exactly the Commission imposed and from when it applies
Commission Implementing Regulation (EU) 2026/1914 was adopted on 5 August 2026 and published in the Official Journal a day later. It entered into force on the day following publication, so it has applied since 7 August 2026, and it imposes a provisional duty on imports of certain lightweight thermal paper originating in China.
A caveat is needed here that no Polish service we know of has made. The title of the Polish version of the act in the Official Journal refers to an anti-dumping duty, but that is a translation error. The English version in the same place refers to a countervailing duty, the legal basis is Article 15 of Regulation 2016/1037, meaning the rules on protection against subsidised imports, and the proceeding was initiated on 7 November 2025 as an anti-subsidy proceeding, following a complaint by the European association of thermal paper producers. The TARIC database also describes this measure as a provisional countervailing duty. For the importer, the difference is not academic: these are two different procedures, with separate deadlines and a separate appeal route, and only this one proceeding concerning thermal paper from China is currently under way. We checked the full list of acts and notices: there is not, and has not been, a parallel anti-dumping investigation against China for this product.
The measure is provisional, so it does not work like an ordinary tariff duty. Release of the goods for free circulation requires a security to be lodged in the amount of the duty. Only the decision on definitive measures will settle whether the security is collected, in what part, and whether it is released. It is also worth knowing where these particular rates come from: they correspond to the established subsidy margins, and the Commission did not apply the lesser duty rule because nobody in the proceeding put forward arguments for using it.
| Item from our register | Value |
|---|---|
| Case | Implementing Regulation (EU) 2026/1914, CELEX 32026R1914 |
| Stage of proceeding | provisional duty |
| Date of measure | 5 August 2026 |
| Type of measure | countervailing duty, that is anti-subsidy |
| Rate | 28.8% for the producer with an individual rate, 70.5% for all other imports |
| CN codes | ex 4809 90 00, ex 4811 90 00, ex 4816 90 00, ex 4823 90 85 |
| Origin | China |
The above comes from our register of anti-dumping and countervailing duties, which we update daily from EUR-Lex and the Commission's database of proceedings. You will find the card for this case and other measures affecting this product group under CN code 4811 90 00.
Product definition: four conditions that must all be met at once
The regulation defines the product concerned as thermal paper with a weight of 65 grams per square metre or less, sold in rolls with a width of 20 centimetres or more, a roll weight of 50 kilograms or more and a roll diameter of 40 centimetres or more. On top of that comes a description of the coatings: with or without a base coat, with a thermal layer on one or both sides, with or without a top coat.
These four figures are not an example description but the boundary of the scope, and they must all be met together. Paper weighing 80 grams falls outside the scope, even if it arrived in a two-tonne roll. A roll 15 centimetres wide falls outside, even if the paper weighs 48 grams per square metre. That is exactly why converted products are outside the measure: converting consists of slitting a jumbo roll into narrow webs and rewinding them onto small diameters, that is, removing from the goods precisely the features that define the product subject to duty.
The strongest evidence, however, lies not in the definition but in the recitals. One of the Chinese producers in the sample withdrew from the proceeding, arguing that its unrelated domestic traders cut jumbo rolls into small ones, and small rolls do not fall within the scope of the investigation, so the company did not in fact export the product concerned to the EU. The Commission accepted that argument and removed the company from the sample. In other words: the Commission itself, in the same act, confirmed that cutting a jumbo roll into small ones takes the goods outside the scope of the measure.
It is worth adding that this is not an exception specific to this one case. The EU today has three customs regimes for thermal paper: this Chinese one, an anti-dumping one against South Korea for lightweight paper, and a separate one for paper heavier than 65 grams, also Korean. Every one of them, without exception, is limited to jumbo rolls.
The comparison below shows how far finished products are from the thresholds. The values for finished products are typical market parameters, not data from the legal act, but the scale of the difference leaves no room for doubt.
| Condition from the regulation | Roll of finished 100x150 mm labels | 80 mm till roll | Jumbo roll |
|---|---|---|---|
| weight up to 65 g/m2 | usually above the threshold together with adhesive and liner | from 48 to 55 g/m2, within the threshold | from 48 to 65 g/m2 |
| roll width from 20 cm | about 10 cm | 8 cm | from 60 to 140 cm |
| roll weight from 50 kg | about 1 kg | below 0.1 kg | from 500 to 2000 kg |
| roll diameter from 40 cm | from 11 to 13 cm | about 8 cm | from 100 to 150 cm |
The CN code is not enough, check the ten-digit TARIC code
Here is the trap that can cause needless panic. A till roll is classified under heading 4811 90 00, one of the four codes listed in the regulation. An importer who sees their code on the list has every right to be alarmed, and that is exactly why the act puts the abbreviation ex next to these codes. It means the heading is covered only partly, to the extent described in words.
In practice, the deciding factor is the ten-digit TARIC code, not the eight-digit CN code. The TARIC database divides these headings into a subheading ending in 10, described precisely as jumbo rolls, and a subheading ending in 90, meaning everything else. The countervailing duty sits only on subheadings 4809 90 00 10, 4811 90 00 10, 4816 90 00 10 and 4823 90 85 20. A till roll goes under 4811 90 00 90, where there is no measure against China and the customs duty rate is zero.
Finished labels are even simpler, because they are no longer paper but an article made of it. Labels of all kinds belong to heading 4821: self-adhesive printed ones to 4821 10 10, self-adhesive ones without factory printing to 4821 90 10. A typical blank white thermal label for a printer is precisely that second subheading. There are no measures against China on either of them, and the customs duty rate is also zero. Self-adhesive material in a continuous roll, not yet die-cut into labels, is classified under heading 4811 41, and there is no measure there either.
Checking your own heading takes literally a moment. In the TARIC tariff search or the Polish ISZTAR browser, you enter your ten-digit code, select China as the country of origin and give the clearance date. The system will list all the measures in force on that day, together with the regulation number. If the result contains no item called countervailing or anti-dumping duty, the matter is closed. If it does, read the subheading description and compare it with the parameters from the packing list.
Three things are worth remembering here. Classification is decided by the state of the goods at the time of the customs declaration, not by the trade name on the invoice, so the seller's description protects you from nothing. The measure applies only to goods originating in China, and thermal paper from South Korea is subject to a separate, older anti-dumping duty as a fixed amount per tonne, so one rate must not be carried over to the other origin. Finally, for a delivery that genuinely falls within the definition, the lower rate requires a signed producer's declaration on the commercial invoice and the correct TARIC additional code. Without that document, the customs authority applies the residual rate, that is 70.5%, even if you buy from a producer with a lower rate.
Do not confuse this with the duty on decor paper
This is the most common mistake on the Polish internet, and it costs more than it seems. For searches about anti-dumping duty on paper from China, the search engine first returns articles about decor paper, covered by an entirely different regulation from February 2025 and entirely different rates. An importer of thermal paper who lands on such an article will put the wrong figure and the wrong act into their calculation, and then be surprised at clearance.
Decor paper is a material for laminates and furniture foils. Thermal paper is a medium for an image created by heat, used in tills, scales and label printers. These are two different products, two different proceedings and two different sets of codes. Before you copy any rate into a spreadsheet, check the regulation number the source refers to and compare it with what TARIC shows for your code.
Why labels may get more expensive anyway
The fact that your goods are outside the scope of the duty does not mean the duty will not affect your cost. The supply chain works like this: jumbo rolls go to a converter, and the converter cuts them into till rolls and labels. Some European converters bought their raw material in China because it was clearly cheaper than the European one. Since 7 August that raw material carries an additional cost at the border for them, so they either go back to paper made in the EU or raise the prices of the finished product. Either way, the result is more expensive thermal paper in Europe, and that is the part of the bill that will reach Polish buyers in the coming quarters.
The scale of what led to the duty is in the regulation itself and explains why the Commission acted so quickly. During the investigation period, the share of imports from China in the EU market grew from 1.4% to 8.2%, and volume increased by 423%. All of these sales undercut EU producers' prices, by 10.4% on average, and the profitability of the EU industry fell over the same period from 15.2% to 1.9%, practically to zero. With figures like these, a proceeding almost always ends in a duty, and the rate is rarely symbolic. We list other trade defence cases opened this year in our overview of new EU proceedings against China.
The reverse direction also matters, and it is worth understanding before anyone builds a purchasing strategy on it. Since the raw material from China carries duty and the finished product from China does not, finished labels and till rolls from China become relatively cheaper than those made in Europe from Chinese paper. The regulation itself shows that this model already works, because Chinese traders cut jumbo rolls into small ones before export. The history of trade proceedings in the EU tells you what usually happens next: the EU industry requests an anti-circumvention investigation or lodges a new complaint covering converted products. There is, however, a strong argument the other way, and it is worth knowing before anyone starts frightening customers with a duty on labels. The EU has had measures on lightweight thermal paper from South Korea since 2016, so for ten years, and in all that time it has not once extended them to small rolls, even though the same cutting mechanism was known from the start. Instead, it dealt with the issue through the form of the duty, setting it as a fixed amount per tonne. So this does not mean labels will certainly get a duty, and there is no proceeding opened on this today. It only means that building an annual contract on the assumption that this difference will survive the whole period the measure is in force is a risk that has to be written into the calculation, not ignored.
What happens next and by when
A provisional duty is not the end state. Interested parties had 15 calendar days from the entry into force of the regulation to submit written comments to the Commission, that is until 22 August 2026, and the Commission now has to gather the material and decide on definitive measures. Two deadlines from the basic regulation converge here almost on the same day. A provisional duty in an anti-subsidy proceeding applies for a maximum of four months, that is until 6 December 2026. The definitive duty must be imposed within thirteen months of initiation, and since the proceeding began on 7 November 2025, the final deadline falls on 7 December 2026. That is a date worth having in your calendar, because with definitive measures not only the rate but also the product scope can change.
There is one more thread that is easy to forget and can prove costly. Imports of this paper had been subject to mandatory customs registration since February 2026. The new regulation suspends that registration but at the same time orders data on goods released for free circulation in the period of up to 90 days before its entry into force to be kept. The Commission notes that no decision on retroactive application of measures has been taken at this stage. It is standard groundwork, not an announcement. The window in question is clearances from 9 May to 6 August 2026, so if you imported jumbo rolls during that time, keep the documents for those declarations ready.
Everything above is a reading of the content of the regulation and the basic rules, not a statement from the customs authority. You can check the status of your tariff heading yourself in TARIC or ISZTAR, and where classification is doubtful the only binding document is a binding tariff information decision. If you want to see the wider picture of how duties and taxes fit together when importing from China, we described it in the article on customs duty and VAT when importing from China.
Frequently asked questions
Does the duty cover finished thermal labels from China? No. The measure covers only paper in rolls at least 20 centimetres wide, weighing at least 50 kilograms and with a diameter of at least 40 centimetres, with a weight of up to 65 grams per square metre. Finished labels are classified under heading 4821, which carries no measure against China, and the customs duty rate is zero.
I buy 57 millimetre till rolls, will I pay 70.5%? No, provided you import them already cut and rewound. A till roll goes under TARIC code 4811 90 00 90, and the duty sits only on the subheading ending in 10, described as jumbo rolls. The eight-digit CN code on its own looks the same, so check the full ten-digit code.
How do I get the 28.8% rate instead of 70.5%? The lower rate is available only for goods made by the company to which the Commission granted it, and only when the declaration is accompanied by a valid commercial invoice with a signed producer's declaration in the wording specified in the regulation and the correct TARIC additional code. Without that document, the authority applies the rate for all other imports.
Will the security I paid be returned? That depends on the decision on definitive measures. The provisional duty is collected in the form of a security, and only the regulation on definitive measures decides whether it is collected in full, in part, or released.
Is this an anti-dumping duty? No, despite the wording of the title of the Polish version of the act. It is a countervailing, that is anti-subsidy, duty imposed under Regulation 2016/1037. An anti-dumping duty on lightweight thermal paper applies to South Korea and is a separate matter.
What about goods already in transit? What matters is the date of release for free circulation, not the date the invoice was issued or the goods were loaded. Goods cleared from 7 August 2026 require a security if they fall within the product scope.
Does shipping the goods through a third country solve the problem? No. The measure concerns the origin of the goods, not the transport route, so transhipment alone changes nothing, and an attempt to change the declared origin without real processing is circumvention of the rules with fiscal penal consequences.
Sources
- Commission Implementing Regulation (EU) 2026/1914 of 5 August 2026 imposing a provisional duty on imports of certain lightweight thermal paper originating in the People's Republic of China, CELEX 32026R1914
- Notice of initiation of an anti-subsidy proceeding concerning imports of lightweight thermal paper from China, OJ C 2025/5911 of 7 November 2025
- Commission Implementing Regulation (EU) 2026/313 of 6 February 2026 making imports of lightweight thermal paper originating in China subject to registration
- Regulation (EU) 2016/1037 of the European Parliament and of the Council on protection against subsidised imports from countries not members of the European Union
- Commission Implementing Regulation (EU) 2023/1330 imposing a definitive anti-dumping duty on imports of lightweight thermal paper from the Republic of Korea
- European Commission TARIC database, status of measures for codes 4809 90 00, 4811 90 00, 4816 90 00, 4823 90 85, 4821 10, 4821 90 and 4811 41 against China, checked 21 August 2026
- ImportPanel register of anti-dumping and countervailing duties, status as of 21 August 2026
